Shop

Description This Water Quality Test Kit is ideal to test the levels of 13 different elements, allowing you to identify potential issues in your water quality so you know how to correctly treat your water. This test kit includes: 1 x SimplexHealth 12 in One & 1 x Watersafe Lead Test Kit and saves £3 compared to buying separately This kit tests for: coliform bacteria, nitrate, nitrite, hydrogen sulfide, total hardness, total alkalinity, total chlorine, free chlorine, copper, sulfate, iron, pH and lead Suitable for: fresh and potable water samples, including water from taps, wells, springs, boreholes, ponds, rain water as well as water stored in tanks. This test kit contains 2 tests for each parameter and 1 test for bacteria & 1 test for lead – totalling 24 tests.   Simple Dip-Wait-Read method Quick and easy to use, no training required Reliable and accurate testing Each kit contains everything required to carry out the tests Convenient way to check water for 13 of the top water quality concerns Results are available immediately, only the bacteria test takes 24 to 48 hours Test kit is easy and safe to use (MSDS is not required) Each kit contains: 1 x coliform bacteria test, with simultaneous E.coli detection 1 x lead test with presence/absence measured at a level of 15ppb (= 0.015 mg/l) 2 Tests for each: free & total chlorine, nitrate & nitrite, hardness, pH, total alkalinity, iron, copper, sulfate and hydrogen sulfide Detailed test instructions, colour chart as well as additional information including how to understand the test results. Because the kit contains 2 tests each (except for bacteria & lead) – it is very suitable to test the effectiveness of your water filtration system. Simply test your water before and after treatment and compare the results. Simple Dip-Wait-Read method This test uses our simple Dip-Wait-Read Method for testing free & total chlorine, nitrate & nitrite, hardness, pH, total alkalinity, iron, copper, sulfate and hydrogen sulfide. To view the full Instructions click here Bacteria Test How to use (please refer to product for detailed instructions): Fill mug with 100ml of water sample to be tested and securely recap bottle. Shake the mug until all media is dissolved, solution should be clear yellow. Incubate for 24 hours or 48 hours, depending on temperature. After incubation time, observe the colour of the sample: a. clear yellow = negative for coliforms; b. blue-green = positive for coliforms E.coli confirmation: shine a blacklight from the bottom of the sample: no fluorescence = negative for E.coli; blue fluorescence = positive for E.coli* Dispose of water sample safely *a blacklight with a wavelength of 365 is recommended , ie. the NVF-4 blacklight PLUS  Lead Test The UK maximum contaminant level for Lead in tap water set by DWI/DEFRA is 10µg/l (= 0.01mg/l = 0.01ppm). Sensitivity: presence/absence measured at a level of 5ppb (= 0.005 mg/l) How to use the lead test: Open Lead packet and take out all contents. The foil packet contains a one test strip, test vial, a dropper pipette, and a desiccant (to be discarded). Using dropper, place water sample into test vial. Swirl vial gently for one minute. Place on a flat surface. Place test strip into the test vial, with arrows pointing DOWN. Wait 10 minutes. Do not disturb strips or vial during this time. Lines will appear on the strip. Take the strip out of the vial and read result. Negative: Bottom line (next to number 1) is darker than the top line (next to number 2). Positive: Top line (next to number 2) is darker than the bottom line (next to number 1), or lines are equally dark.   A Sensitivity & Test time: Test Sensitivity Result Time Iron 0.0, 0.05, 0.1, 0.3, 1.0 ppm (mg/l) 25 seconds Copper 0.0, 0.1, 0.5, 1.0, 2.0 ppm (mg/l) 50 seconds Nitrate 0, 2, 10, 20, 50 ppm (mg/l) 1 minute Nitrite 0, 0.2, 1, 1.5, 3 ppm (mg/l) 1 minute pH 2, 4, 5, 6.5, 8.5, 9.5, 10.5, 12 30 seconds Total Alkalinity 0, 40, 80, 120, 180, 240, 500 ppm (mg/l) 30 seconds Total Chlorine 0, 0.1, 0.2, 0.5, 0.8, 1, 4, 10 ppm (mg/l) 40 seconds Total Hardness 0, 50, 120, 250, 425, 1000 ppm (mg/l) 30 seconds Free Chlorine 0, 0.05, 0.2, 0.6, 1.5, 4, 10 ppm (mg/l) 45 seconds Sulfate 0, 250, >500 ppm (mg/l) 35 seconds Hydrogen Sulfide 0.3, 0.5, 1, 2 ppm (mg/l) 30 seconds Bacteria* present/absent 24-48 hours Lead presence/absence measured at a level of 5ppb (= 0.005 mg/l) 10 minutes *The bacteria test kit detects total coliform (which is  faecal bacteria for the most part) and is a presence/absence test of 1cfu/ml. Should the result be positive, then the presence of E.coli can be detected using a blacklight with a wavelength of 365 (like the NVF-4 blacklight). Not sure which is the right water testing kit for you? Click here to compare our range of multi-pack options. Please note: that this is a screening test and can not be used to certify water as safe or unsafe for drinking. This test kit provides approximate results ONLY when used in strict accordance with instructions. SimplexHealth expressly disclaims any liability resulting from the use of this product, failure to follow instructions or reliance of test results. This is not a measuring instrument. Store in a cool, dry (below 32°C) place and away from excess heat and direct sunlight. No MSDS required. Keep away from children and pets. Avoid contact of test areas on strips with skin & eyes, do not ingest or expose to acids. Do not touch test pad and do not consume water which has been tested. MPN: SH13-in-1